• OBD-II接口定義 OBD-II NETWORK STANDARDS

    2019-03-06 14:20:07 root 1207

    All cars and light trucks built for sale in the United States after 1996 are required to be OBD-II compliant. There are five OBD-II protocol types in use: J1850 PWMJ1850 VPWISO 9141-2ISO 14230 KWP2000, and ISO 15765 CAN.

     

     

    obd

     


    SAE J1850 PWM  (Pulse Width Modulation at 41.6 Kbps, two wire differential)

    Pin 2: BUS+ signal
    Pin 10: BUS- signal
    Active bus state: BUS+ is pulled high while BUS- is pulled low
    High signal voltage level: +5V (min/max 3.80 to 5.25)
    Low signal voltage level: 0V (min/max 0.00 to 1.20)
    Up to 12 message bytes, excluding frame delimiters
    Bit Timing;

    "1" Bit: Bus state active for 8uS (within 24uS bit period)
    "0" Bit: Bus state active for 16uS (within 24uS bit period)
    Start-Of-Frame: Bus state active for 48uS

     

     

    obd

     


    SAE J1850 VPW  (Variable Pulse Width at 10.4/41.6 Kpbs, single wire)

    Pin 2: BUS+ signal
    Idle bus level is low
    High signal voltage level: +7V (min/max 6.25 to 8.00)
    Low signal voltage level: 0V (min/max 0.00 to 1.50)
    Up to 12 message bytes, excluding frame delimiters
    Bit Timing;
    "1" Bit: Signal low for 128uS or high for 64uS
    "0" Bit: Signal low for 64uS or high for 128uS
    Start-Of-Frame: Signal high for 200uS

     

     

    obd

     


    ISO 9141-2   (Asynchronous serial communication at 10.4 Kbaud)

    Pin 7: K-line bidirectional for communication
    Pin 15: L-line (optional) unidirectional for waking up the ECU
    Idle signal levels are high
    Signals are active pull-down to 0V (0.00 to 2.40)
    High signal voltage level: +12V (min/max 9.60 to 13.5)
    Up to 12 message bytes, excluding frame delimiters
    Bit Timing;

    UART signaling at 10.4K baud, 8 data bits, no parity, 1 stop

     

     


    ISO 14230 KWP2000   (Asynchronous serial communication up to 10.4 Kbaud)

    Pin 7: K-line bidirectional for communication
    Pin 15: L-line (optional) unidirectional for waking up the ECU
    Idle signal levels are high
    Signals are active pull-down to 0V (0.00 to 2.40)
    High signal voltage level: +12V (min/max 9.60 to 13.5)
    Message may contain up to 255 bytes in the data field
    Bit Timing;

    UART signaling up to 10.4K baud, 8 data bits, no parity, 1 stop

     

     

    obd

     


    ISO 15765 CAN   (250kbit/sec or 500kbit/sec)

    Pin 6: CAN high (CANH)
    Pin 14: CAN low (CANL)
    Dominant or active bus state: CANH driven high while CANL driven low
    Recessive or idle bus state: CANH and CANL signals are not driven
    CANH signal voltage level: 3.5V (min/max 2.75 to 4.50)
    CANL signal voltage level: 1.5V (min/max 0.5 to 2.25)

     

    目前,J1850基本上已沒有什么車型使用,大部分采用后三種協議,就是我們俗稱的K線CAN線。

    電話咨詢
    公司地址
    解決方案
    QQ客服
    欧美在线视频国产网红,愉自拍2区视频,欧美一级,美国三级,97色在色在线播放免费,久久久噜噜噜久久,国产欧美一区二区三区,日本不卡免费视频新二区